PhET The Floating Balloon — Lab Worksheet & Guide
Open Simulation

The Floating Balloon

Virtual PhET-Style Lab Worksheet & Simulation Step-by-Step Guide

★ Objective

Calculate the number of balloons that would be required to allow the house in the movie "UP" to float motionless in equilibrium.
Before You Begin (Simulation Setup)

1 Set Up Your Balloon Screen 1: Balloon Lab

  1. Choose one helium balloon from the Balloon Rack on the left (or under Select Balloon on the right) and record your choice below:
Selected Balloon:
  1. Attach the paperclip to the balloon's ribbon: drag the Paperclip from SUPPLIES onto the tip of the ribbon (or click Attach Paperclip).
  2. Hang the cardstock from the paperclip: drag the Cardstock onto the paperclip (or click Hang Cardstock).
  3. Wait ~2 seconds and confirm the added mass is heavy enough to pull the balloon down onto the lab bench (On Bench, Height (y) = 0.00 m).

2 Achieve Equilibrium Screen 1: Balloon Lab

  1. Click Cut Cardstock in the bottom tray, then click across the hanging cardstock to cut strips off — or use the precision trim buttons (-1.0 g, -0.1 g, +0.1 g, +1.0 g).
  2. Test hovering by clicking Lift to Midair (or drag the balloon to 1.00 m and release):
    • If status reads Falling, it is still too heavy → cut more cardstock.
    • If status reads Rising, you cut too much → click Undo, +0.1 g, +1.0 g, or New Cardstock.
  3. Repeat until the balloon hovers motionless in midair (Equilibrium!, v = 0.00 m/s, a = 0.00 m/s²).
  4. Use the interactive colored drawing pad on the left to draw the balloon's Free Body Diagram in midair equilibrium (choose colors for F_B and F_g, drag from the center dot to draw arrows, and stamp force labels).

3 Measure the Forces Screen 1: Balloon Lab

  1. Click Weigh Assembly (or turn off Cut Cardstock and drag the paperclip + cardstock onto the ELECTRONIC BALANCE pan).
  2. Confirm the balance status says Pan: Paperclip + Cardstock so both the cardstock AND paperclip are included. (If a TARE badge appears when the pan is empty, click TARE / ZERO to clear it.)
  3. Click g / kg to display mass directly in kilograms (kg), and record Added Mass (kg) below.
  4. Calculate Added Weight (N) using W = m · g. Since a hovering balloon is in equilibrium, record the Buoyant Force (N) that the single helium balloon provides.
Self-Check in Simulation: Click Return to Balloon → Lift to Midair, then check Values (N) and Net Force in Display Options to verify your calculated forces!
Added Mass (kg)
Added Weight (N)
Buoyant Force (N)

4 Could "Up" Occur in Real Life? Screen 2: "Up" House

In the movie "Up", the characters float away in a house supported by many helium balloons. Assume the balloons and rigging add no noticeable mass to the house. House Mass: 45,000 kg
  1. Switch to "Up" House in the bottom black bar. Confirm the Single-Balloon Lift box synced the balloon you measured in Screen 1 (or check Custom F_B per balloon (N) to type your value).
  2. Uncheck Values (N) while solving: calculate House Weight (N) (W = 45,000 · g), the required Buoyant Force (N) for Net Force = 0 N, and how many single balloons are required (N = F_B / F_B,1).
  3. Test in Simulation: Enter your calculated number of balloons in Number of Balloons, click Apply (or press Enter), and click Test Hover (20 m). Confirm status shows Equilibrium! (v = 0.00 m/s, a = 0.00 m/s²), then check Values (N) to verify your table!
Net Force 0 N
House Weight (N)
Buoyant Force (N)

5 Bonus — Liftoff Acceleration (a = 0.5 m s⁻²) Screen 2: "Up" House

In the movie, when the 45,000 kg house first lifts off of the ground, it rises with an upward acceleration of 0.5 m s⁻². Since there is a non-zero upward acceleration, the buoyant force from the balloons must be greater than the weight of the house.

  1. Click Reset to Ground so the house starts anchored on the ground (Altitude (y) = 0.0 m).
  2. Calculate Net Force (F_net = m · a = 45,000 · 0.5), House Weight (N), required Buoyant Force (N) (F_B = W + F_net), and the required balloon count (round up to a whole balloon).
  3. Test in Simulation: Enter your balloon count into Number of Balloons, click Apply, and click Release / Launch. Confirm the Motion card shows steady Accel. (a) = +0.50 m/s² as the house rises!
  4. Enable Free Body Diagram, Net Force, and Values (N) to verify your calculations, and draw the Bonus Free Body Diagram on the interactive pad on the left (make F_B longer than W, and add upward F_net).
Net Force (N)
House Weight (N)
Buoyant Force (N)